Pular para o conteúdo
We are climate neutral since 2010

Sensor de inclinação N5

Sensor de inclinação N5

  • Elevada vida útil e confiabilidade devido à tecnologia MEMS
  • Range de medição 360° para um eixo ou 180° para dois eixos
  • Até 4 pontos de medição digital programável
  • Seleção de delay para funções liga/desliga por sinal de saída
  • Ajuste da posição neutra através de controle remoto ou através da rede CAN bus
  • Classe de proteção IP67
  • Temperatura de trabalho -40 °C to +85 °C
  • Conector Deutsch ou plug M12
  • Conexão em série: loop através do sinal CAN sem necessidade de conectores T adicionais
  • Compacto e robusto, adequado também para ambientes externos
  • Redundância para aplicações que exigem nível de segurança mais elevados

O sensor de inclinação modelo N5 com interface CAN-Bus está disponível nos protocolos de comunicação CANopen ou SAEJ1939. Este sensor possui elevada resistência à impactos e vibrações, portanto é muito utilizado para medição de inclinação em máquinas agrícolas, máquinas de construção, caminhões fora de estrada entre outras aplicações severas. O sensor de inclinação N5 pode ser facilmente programado e a posição neutra ajustada através de um controle remoto infravermelho.

Características do artigo

  • N5ACJ...
  • N5ACJB...
  • N5ACO...
  • N5ACOB...
  • N5ECJ...
  • N5ECJB...
  • N5ECO...
  • N5ECOB...
  • N5GCJ...
  • N5GCO...
  • N5ICJ...
  • N5ICO...
  • N5KCJ...
  • N5KCO...
  • N5LCJ...
  • N5LCO...
  • Max. switching voltage
  • Max. switching current
  • Max. switching power
  • Polarity reversal protection
  • Resolution
  • Operating voltage min.
  • Operating voltage max.
  • Current consumption
  • Short-circuit resistance to GND
  • Short-circuit resistance to supply
  • Repeating accuracy
  • Signal update rate
  • Technology
  • Number of measurement axes (Number)
  • Angle measuring range
  • Initialisation time after power on/start-up time
  • Switching points
  • Zero justification
  • Vibration filter
  • Fieldbus system
  • Protocol
  • Node ID / Source Address
  • Transmitting cycle
  • Baud rate
  • Bus terminating resistor
  • MTTF
  • Switching output
  • Outputs
  • Turn-on delay
  • Turn-off delay
  • Connection type (switching output)
  • Temperature coefficient
  • Linearity error
  • Protection class
  • Operating temperature min.
  • Max. operating temperature
  • Min. storage temperature
  • Max. storage temperature
  • Shock resistance (Norm)
  • Vibration resistance (Norm)
  • Impact resistance (Norm)
  • EMC Agricultural and forestry machines (Norm)
  • EMC Earth-moving and building construction machinery (Norm)
  • EMC Industrial trucks (Norm)
  • Torque for fastening screws
  • Weight
  • Connection
  • CE label
AttributeN5ACJ...N5ACJB...N5ACO...N5ACOB...N5ECJ...N5ECJB...N5ECO...N5ECOB...N5GCJ...N5GCO...N5ICJ...N5ICO...N5KCJ...N5KCO...N5LCJ...N5LCO...
Bestellung
Bestellung
Max. switching voltage 48 V DC 48 V DC 48 V DC 48 V DC
Max. switching current 1 A 1 A 1 A 1 A
Max. switching power 30 W 30 W 30 W 30 W
Polarity reversal protection yes yes yes
Resolution 0.014 ° 0.014 ° 0.014 °
Operating voltage min. 9 V DC 9 V DC 9 V DC
Operating voltage max. 32 V DC 32 V DC 32 V DC
Current consumption 100 mA 100 mA 100 mA
Short-circuit resistance to GND yes no yes no yes no yes no yes yes
Short-circuit resistance to supply yes no yes no yes no yes no yes yes
Repeating accuracy < 0,3 ° < 0,3 ° < 0,3 °
Signal update rate 200 Hz 200 Hz 200 Hz
Technology MEMS MEMS MEMS
Number of measurement axes (Number) 2 2 (X, Y) Z-axis for signaling the installation position 2 2 (X, Y) Z-axis for signaling the installation position 2 2 (X, Y) Z-axis for signaling the installation position 2
Angle measuring range 180 ° 360/120 ° 180 ° 360/120 ° 180 ° 360/120 °
Initialisation time after power on/start-up time 500 ms 500 ms 500 ms
Switching points Selectable from ±1.5°...±90 ° Selectable from ±1.5°...±90 ° Selectable from ±1.5°...±180 ° Selectable from ±1.5°...±180 °
Zero justification ±60° ±60° ±60°
Vibration filter 25 Hz 25 Hz 25 Hz
Fieldbus system CAN CAN CAN
Protocol J1939 CANopen J1939 CANopen J1939 CANopen J1939 CANopen J1939 CANopen J1939 CANopen
Node ID / Source Address 0xE2 0x20 0xE2 0x20 0xE2 0x20 0xE2 0x20 0xE2 0x20 0xE2 0x20
Transmitting cycle 10 ms 10 ms 10 ms
Baud rate 250 kBit/s 250 kBit/s 250 kBit/s
Bus terminating resistor no no no
MTTF 57.6 a 57.6 a 57.6 a
Switching output 2x NO 2x NO 2x NO 2x NO
Outputs CAN J1939 CAN J1939 + relay CANopen CANopen + relay CAN J1939 CAN J1939 + relay CANopen CANopen + relay CAN J1939 CANopen CAN J1939 CANopen CAN J1939 CANopen CAN J1939 CANopen
Turn-on delay Selectable (0…2 s in 0.5s increments) Selectable (0…2 s in 0.5s increments) Selectable (0…2 s in 0.5s increments) Selectable (0…2 s in 0.5s increments)
Turn-off delay Selectable (0…2 s in 0.5s increments) Selectable (0…2 s in 0.5s increments) Selectable (0…2 s in 0.5s increments) Selectable (0…2 s in 0.5s increments)
Connection type (switching output) Selectable Selectable Selectable Selectable
Temperature coefficient ± 0,02°/K ± 0,02°/K ± 0,02°/K
Linearity error < ± 0,4° < ± 0,4° < ± 0,4°
Protection class IP67 DIN EN 60529 IP67 DIN EN 60529 IP67 DIN EN 60529
Operating temperature min. -40 °C -40 °C -40 °C
Max. operating temperature 85 °C 85 °C 85 °C
Min. storage temperature -40 °C -40 °C -40 °C
Max. storage temperature 105 °C 105 °C 105 °C
Shock resistance (Norm) 500 m/s²;, 100 shocks per axis, DIN EN 60068-2-27 500 m/s²;, 100 shocks per axis, DIN EN 60068-2-27 500 m/s²;, 100 shocks per axis, DIN EN 60068-2-27
Vibration resistance (Norm) Sine Vibration: 100 m/s²;, 19h, DIN EN 60068-2-6 Random Vibration: 80,1 m/s²;, 24h, DIN EN 60068-2-64 Sine Vibration: 100 m/s²;, 19h, DIN EN 60068-2-6 Random Vibration: 80,1 m/s²;, 24h, DIN EN 60068-2-64 Sine Vibration: 100 m/s²;, 19h, DIN EN 60068-2-6 Random Vibration: 80,1 m/s²;, 24h, DIN EN 60068-2-64
Impact resistance (Norm) max. 50 g max. 50 g max. 50 g max. 50g
EMC Agricultural and forestry machines (Norm) DIN EN ISO 14982
pulse 5b: max. voltage 65 V (absolute), functional status C for pulse 1 and 4
DIN EN ISO 14982
pulse 5b: max. voltage 65 V (absolute), functional status C for pulse 1 and 4
DIN EN ISO 14982
pulse 5b: max. voltage 65 V (absolute), functional status C for pulse 1 and 4
EMC Earth-moving and building construction machinery (Norm) DIN EN ISO 13766-1
pulse "load dump": max. voltage 65 V (absolute)
DIN EN ISO 13766-1
pulse "load dump": max. voltage 65 V (absolute)
DIN EN ISO 13766-1
pulse "load dump": max. voltage 65 V (absolute)
EMC Industrial trucks (Norm) DIN EN 12895 DIN EN 12895 DIN EN 12895
Torque for fastening screws 6 N m 6 N m 6 N m
Weight 100 g 100 g 100 g
Connection Deutsch 8-pol. Deutsch 8-pol. M12x1 5-pol. 2 x M12x1 5pol.
CE label yes yes yes

Avaliações de clientes

Produto adicionado à lista de referência.

Data security and the limitation of data collection are very important to us. Further information on this can be found in our data privacy policy.

I agree that elobau GmbH & Co.KG and the subsidiaries group may contact me by e-mail or telephone. This can be revoked at any time by sending an e-mail message to datenschutz@elobau.de. The data provided are electronically transmitted by elobau GmbH & Co KG or to its subsidiaries, stored in the internal e-mail system and processed for offers and consultation. While the data may be stored by the provider under certain circumstances, it is handled in compliance with data protection regulations and subsequently deleted. Furthermore, the data remains with elobau group and is not disclosed to third parties, unless the inquiry is made from without the countries in which the companies are located, and disclosing the data to one of our trading partners is required in order to process the inquiry. I am aware that this may be a country outside the EU. I agree to this by the submission of this form.

The data sent will only be processed for the purpose of processing your inquiry. The data will be deleted as soon as it is no longer required for its original purpose. You can withdraw your consent at any time without providing a reason at: datenschutz@elobau.de. There are no adverse consequences. You have a right to information, deletion and restriction of the processing of your personal data.
Accept privacy policy
Todos os campos marcados com * são obrigatórios.